Vogel's TVM 5845 black

Swivel wall mount for 55 to 100-inch screens

A large TV mounted on the wall usually stays facing the sofa, even when the room also has a table, a kitchen area or a second armchair. This dual-arm mount from the Elite series keeps a 55 to 100-inch screen weighing up to 55 kg just 4 cm from the wall when folded, then extends it into the room and turns it towards wherever you are watching from.

Flush against the wall or extended by 74 cm

When folded, the mount leaves 4 cm between the back of the TV and the wall, a distance close to that of a fixed mount. With a slim-edged OLED or QLED, this gap matters: a screen floating ten centimetres from the wall loses the slim appearance you chose it for. When extended, the two 74 cm arms carry the screen up to 74 cm from the wall, enough to bring it out of a recess or move it past a corner.

This is the longest reach in the Elite Full-Motion+ series. The TVM 5645 extends to 65 cm for 40 to 77-inch screens weighing up to 45 kg, while the TVM 5445 covers 32 to 65-inch screens weighing up to 35 kg. The structure is made of steel (just over 6 kg of metal in total), with a black finish and a 360 mm-high wall plate.

Three pivot points and one-finger rotation

The arms have three pivot points, used to extend the screen, move it sideways and adjust its direction. Rotation reaches a total of 180°, or up to 90° on either side, with one limitation dictated by geometry: the wider the screen, the sooner its edge meets the wall, and a 100-inch screen cannot turn as far as a 55-inch screen. The OneFinger movement relies on coated bearings and precision steel shafts, and the screen moves with one finger, without stiff spots or jerks.

The mount does not tilt, and this is a deliberate choice: with panels this thin, tilting adds mechanical stress every time they are moved and increases the risk of damaging the screen. The drilling height must therefore be set accordingly, as the vertical angle cannot be adjusted afterwards.

A level screen even after the screws are tightened

A hole drilled a few millimetres too low, a wall plug pulling slightly to one side, a wall that is not perfectly flat: the 2D Leveling adjustment corrects the horizontal alignment of the image and the vertical alignment of the screen afterwards, without redrilling or dismantling. On the TV side, soft pads sit between the metal mounting interface and the back of the set, which is often fragile on very thin models.

Cables that follow the arms

The Cable Inlay System houses the cables inside the arms themselves, so they follow the movements without dangling or getting caught in the joints. Holders secure the cables at the back of the TV, and finishing covers close everything off. For the run down the wall to the cabinet, the TVA 7000 cable cover is available in black and white.

From the drilling template to the DrillRight app

The box contains the mount, the wall mounting kit with fischer DuoPower wall plugs, the TV mounting kit, a spirit level, a drilling template and a quick installation guide. The DrillRight app, available on iOS and Android, adds a spirit level to your phone and helps mark the first hole in the right place, the step where most installation mistakes happen.

DuoPower wall plugs are suitable for concrete and brick. A 55 kg TV extended 74 cm from the wall exerts considerable leverage on the upper fixings: a lightweight partition wall is not suitable as it stands, and a stud wall requires the TVA 6950 adapter.

Certified strength and published environmental assessment

The mount is TÜV-certified and tested to three times its maximum load, or 165 kg. It comes with a 15-year warranty. Vogel’s also publishes an Environmental Product Declaration (EPD), a standardised document that quantifies the product’s impact over its life cycle: 22 kg CO₂ equivalent for this model, which is declared 100% recyclable.

Technical specifications

Type and compatibility

• Type: dual-arm full-motion TV wall mount
• Compatible screen size: 139.7 to 254 cm
• Maximum load: 55 kg
• Supported VESA mounting patterns: 100 × 100, 100 × 200, 200 × 100, 200 × 200, 200 × 300, 300 × 200, 300 × 300, 400 × 200, 400 × 300, 400 × 400, 500 × 200, 500 × 300, 500 × 400, 600 × 200, 600 × 300, 600 × 400 mm
• Maximum VESA mounting pattern: 600 × 400 mm
• TV mounting interface: universal design
  • Maximum height: 425 mm
  • Maximum width: 660 mm

Swivel and adjustments

• Swivel: up to 180° in total
  • Up to 90° left and right, depending on screen size
• Number of joints: 3 pivot points
• Tilt: no, feature intentionally omitted according to Vogel’s
• OneFinger movement: rotate the screen with a single finger
• 2D Leveling: horizontal and vertical adjustment after installation

Cable management and protection

• Cable management: Cable Inlay System (CIS) integrated into the arms, cable holders on the back of the TV, finishing covers
• TV protection: soft pads against the back of the TV

Included accessories and installation assistance

• Package contents: wall mount, wall mounting kit with fischer DuoPower wall plugs, TV mounting kit, spirit level, quick installation guide, drilling template
• Installation assistance:
  • DrillRight app for iOS and Android, with spirit level

Certifications, environment and warranty

• Certifications: TÜV, EPD
• Strength testing: tested up to three times the maximum load
• Recyclability: product declared 100% recyclable
• Carbon footprint: 22.0 kg CO₂ equivalent
• Warranty: 15 years

Accessories offered by Vogel’s

• TVA 7000 TV cable cover:
  • Black: reference 6870000
  • White: reference 6870001
• TVA 6950 stud adapter: reference 6869500
• SOUND 3550 soundbar mount: reference 8153550
• TVA 6400 media box holder: reference 6864000

Dimensions and materials

• Arm length: 74 cm
• Distance from wall:
  • Minimum: 40 mm
  • Maximum: 740 mm
  • Maximum stated in the PDF product sheet: 742 mm
• Wall plate height according to the manufacturer’s diagram: 360 mm
• Materials according to the environmental data sheet for the TVM 5840 series:
  • Steel: 6038 g
  • Plastics: 412 g