Skip to content
HomeCineSolutionsFrance
EN
Quote
Contact
Account
Basket

Sugden Audio MasterClass PA-4 titanium

€3,350

Caution! Borrowing money costs money.

Available on order
Delivery on 27 November 2026 (free)
Fast delivery: on 25 November 2026
Notify me when it's back in stock
Protect your product
+€359
Extended warranty to 5 years +
Accidental damage cover for 3 yearsWhat are the benefits?

Overview

Two moving coil cartridges and one moving magnet cartridge can remain connected at the same time, with switching handled by the front-panel selector. A turntable with two tonearms or two turntables side by side can therefore be connected without unplugging anything. The preamplifier is hand-assembled in Yorkshire and operates entirely in Class A, with a separate circuit for each cartridge type.

Two Class A stages, one for each cartridge type

A moving coil (MC) cartridge delivers a much lower voltage than a moving magnet (MM) cartridge. On the PA-4, input sensitivity is 0.15 mV for MC versus 3.5 mV for MM, a difference of more than twentyfold. Sugden therefore does not route both through the same circuit. The MC stage uses current feedback, which is well suited to very low voltages, while the MM stage uses voltage feedback. RIAA equalization takes place within the feedback loop. This standardized curve restores the balance between bass and treble, as record cutting attenuates the bass and boosts the treble.

Both stages operate in Class A: the transistors conduct continuously, even when no music is playing. There is therefore no switching from one transistor to another, eliminating crossover distortion. The trade-off is that the unit runs hotter than a conventional circuit. DC servo circuits correct DC voltage drift without a capacitor in the signal path, which runs directly from the MC input to the output. Frequency response stays within ±0.3 dB from 10 Hz to 30 kHz, and the signal-to-noise ratio exceeds 70 dB.

A current-shunt-regulated power supply

Sugden considers the power supply a preamplifier stage in its own right. It is a current-shunt design and uses a voltage regulator developed in-house. Its role is to limit the rise in power supply impedance at high frequencies. With a power supply whose impedance rises in the treble, the music signal ends up modulating the supply voltage itself. The circuit boards are gold-plated, and the components have been chosen for their long-term stability. Like all units in the MasterClass series, the PA-4 is assembled from start to finish by a single technician at Sugden’s factory in Heckmondwike.

MC loading at 470 or 100 ohms, with factory customization

The load is the impedance the preamplifier presents to the cartridge. It affects treble response, particularly with MC cartridges. The MM input is set to the standard value of 47 kΩ. Both MC inputs are set to 470 Ω by default. To change either one to 100 Ω, simply insert the supplied loading plugs into the dedicated sockets on the rear panel, one pair per MC input. Other resistive plugs provide values below 470 Ω. A higher value, however, is set at the factory or by the distributor, as is an MM load other than 47 kΩ. If the cartridge has already been chosen when ordering, the PA-4 can therefore be set up specifically for it.

Three inputs, two outputs and a single selector

Connections are via RCA sockets. The three stereo inputs (MC1, MC2 and MM) are on the rear, along with two pairs of line-level outputs at 360 mV. These outputs have Teflon insulators and gold-plated contacts. The second pair can feed a recorder or a second preamplifier, such as a headphone amplifier. The front panel has only the standby button on the left and the input selector on the right, with an indicator light for the selected input. Input switching is handled by relays with gold-plated contacts, which briefly mute the signal to prevent clicks through the speakers. The mains switch is integrated into the power inlet on the rear.

A 430 mm chassis matching the MasterClass series

In a titanium finish, the PA-4 measures 430 mm wide, like the other units in the MasterClass range, by 110 mm high and 330 mm deep (6 kg packed). Since it operates in Class A, it needs space around it for ventilation: not on a carpet, in an enclosed cabinet or next to a heat source. A stable location, away from vibrations, is well suited to it. Sugden also notes that the circuit, with its wide bandwidth, benefits from good-quality interconnect cables. Switching off nearby digital devices while listening to vinyl can also reduce interference.

Technical specifications

Architecture and design

  • Independent phono stages for MM and MC cartridges
  • Class A MC circuit with current feedback (Current Feedback)
  • Class A MM circuit with voltage feedback (Voltage Feedback)
  • RIAA equalization integrated into the feedback loop
  • DC servo circuits enabling direct coupling of the music signal between the MC input and the output
  • Current Shunt power supply
  • Specially developed voltage regulator to limit the increase in impedance at high frequencies
  • Gold-plated circuit boards
  • Hand assembly using components selected for their quality and long-term stability

Connectivity

  • Inputs
    • 2 Moving Coil (MC) inputs
    • 1 Moving Magnet (MM) input
  • Outputs: 2 line-level outputs

Front-panel controls

  • Input selection: MC1, MC2, MM
  • Standby mode (Standby)
  • Selected input indicator

Load settings

  • Matching the PA-4 to phono cartridges: several options
  • MM load: 47 kΩ
  • MC load: 470 Ω / 100 Ω
  • Additional load settings available on request from the manufacturer, to precisely match the preamplifier to the cartridge used

Performance

  • Output level: 360 mV
  • Input sensitivity
    • MM: 3.5 mV
    • MC: 0.15 mV
  • Frequency response: 10 Hz – 30 kHz (±0.3 dB)
  • Signal-to-noise ratio: greater than 70 dB

Dimensions and weight

  • Dimensions (H × W × D): 110 × 430 × 330 mm
  • Packed weight: 6 kg

Frequently asked questions

Can the PA-4 be connected to an amplifier's phono input?

No. Its output is line-level and must be connected to a line input (AUX, CD or equivalent). Through a phono input, the signal would be amplified and equalized twice. The bass would then be greatly exaggerated and the signal would clip.

How much gain does the PA-4 provide?

The ratio between the input sensitivity and the output level of 360 mV gives approximately 40 dB on the MM input and approximately 68 dB on the MC inputs. This headroom is sufficient for most low-output MC cartridges, down to 0.15 mV.

Where should I connect a high-output MC cartridge?

Into the MM input. High-output MC cartridges, around 2 mV, are designed for a moving magnet input loaded at 47 kΩ. MC inputs would give them too much gain.

Does the PA-4 have balanced XLR inputs or outputs?

No. All connections are RCA, including the three inputs and the two pairs of outputs. A turntable with a balanced output connects using an XLR-to-RCA cable.

Should the PA-4 be turned off after each listening session?

Sugden recommends leaving it powered on using the rear switch and using the standby setting on the front panel between listening sessions. It is best to switch it off completely only for a prolonged absence. At startup, the output remains muted for a few moments: this is the normal relay delay.

Is the PA-4 available in other colors?

Yes. Sugden’s Custom Shop service offers custom-coloured front panels for new units only, at an additional cost and with a longer lead time. The knobs and surrounds remain titanium or black. An all-black Stealth finish is also available (front panel, surrounds, knobs and lettering).

Can the cartridge be changed without sending the unit back to the factory?

Yes, as long as the cartridge operates at 47 kΩ in MM mode, or at 470 Ω or less in MC mode. For a lower load, simply use the resistive plugs at the rear. A return to the distributor is only necessary for an MC load above 470 Ω or an MM load other than 47 kΩ.

  • Eco-contribution included in the sale price.
  • Manufacturer reference: S011T
HomeCineSolutions
Loading