Leif
Fits Focal Theva perfectly.
Comment from 10 September 2026 — Experience from 28 August 2026
Placed on a low cabinet or a shelf, a bookshelf speaker rarely plays at the right height, and its vibrations pass into the surface supporting it. Focal designed this 55 cm stand for its Chora 806: the speaker screws onto it, the brushed black MDF column echoes the lines of the range, and the whole assembly tilts slightly backwards so that the tweeter and bass driver speak with one voice at the listening position.
In a two-way speaker such as the Chora 806, sound does not originate from the same plane depending on whether it comes from the 25 mm inverted-dome tweeter or the 16.5 cm Slatefiber mid-bass driver: their emission points sit at different depths, and the two signals do not reach the listener at exactly the same instant. The stand corrects this offset through its very shape. Its column tilts backwards, moving the top of the speaker back and bringing the two drivers into phase at the listener’s position. Focal calls this principle Time Alignment, and the intended effect is a clearer soundstage, better centred on the person sitting facing the speakers.
This tilt is fixed. It delivers the best results in a conventional setup, with the listener seated a few metres from the speakers; listening while standing or from very close up benefits less. Once the Chora 806 is installed, the top of the speaker stands just over 98 cm above the floor (excluding spikes), placing the tweeter around ear level for someone sitting on a sofa or in an armchair.
The top plate has a position for a screw that fits into the underside of the speaker. The Chora 806 therefore does not simply rest on the stand: the two elements form a single unit, limiting unwanted vibrations between the speaker and its support and preventing any slipping, a reassuring feature in a living room used by children or pets. With a 7.35 kg speaker on top of a 3.8 kg stand, the fastening also matters for the stability of the whole assembly, especially as the column tilts backwards.
Focal supplies spikes and pads in the box, allowing floor contact to be adapted to the room’s flooring.
The stand is made of MDF, a dense, low-resonance board of compressed wood fibres, the same type of material used for many speaker cabinets, including the Chora 806. The brushed black finish echoes the sharp edges and understated colours of the Chora range. Beneath a black Chora 806, the assembly looks like a single piece; beneath the light wood or dark wood finishes, the stand acts as a dark, discreet base that shows off the cabinet.
The Chora 806 has been replaced in the Focal catalogue by the Theva N°1, a two-way bookshelf speaker that features the TNF aluminium-magnesium tweeter and the 16.5 cm Slatefiber driver. The stand offered by Focal for the Theva N°1 and Vestia N°1 lists the same dimensions in its specifications as the Chora 806 stand: the same 55 cm height, the same 3.8 kg weight, the same MDF body tilted for Time Alignment, and the same screw position. The Theva N°1, slightly more compact than the Chora 806 (39.2 × 21.2 × 26 cm versus 43.1 × 21 × 27 cm), therefore fits onto this stand without modification.
Spikes are suitable for textile flooring. They pass through the carpet or rug to rest on the floor slab and prevent the stand from wobbling. On parquet, tile or stone flooring, pads are preferable: they protect the surface from scratches and provide a stable base. On delicate parquet flooring, the spikes can also be placed on spike cups, purchased separately.
No. The height of 55 cm and the tilt angle are fixed by the shape of the column. Only the spikes or pads slightly alter the final height, and the spikes can be used to compensate for a floor that is not perfectly level.
The top plate is sized to fit the footprint of these Focal speakers, approximately 21 cm wide by 26 to 27 cm deep. A speaker from another range may fit on it if its base is comparable, but it may not be compatible with the screw mounting, and the tilt, calculated for the Focal two-way speakers, will not have the same effect on another model. A speaker wider or deeper than the top plate would overhang and become unstable.
It all depends on the location of the bass-reflex port, the opening that reinforces the bass. The Chora 806 has its port on the front, making it more tolerant of being close to a wall: it can be placed nearer the wall without the bass becoming overpowering. The Theva N°1 has its port at the rear and needs more space behind it, otherwise the bass can become boomy. In both cases, a few listening tests, moving the speakers forwards or backwards a few centimetres, will help you find the right balance.
The classic starting point is to form a roughly equilateral triangle between the two speakers and the listening position, then angle each speaker slightly towards the listener. The stand’s backward tilt already sets the vertical alignment; the horizontal orientation is fine-tuned to suit the room, with more or less toe-in depending on the desired soundstage width.
Yes, for Chora 806 or Theva N°1 speakers used as front left and right speakers, or as surround speakers placed on either side of the sofa. For surround channels, placement recommendations for multichannel formats generally position the speakers at ear level or slightly above, which corresponds to the height achieved with this stand.
Based on reviews from customers who purchased this product, summarised by AI
Leif
Fits Focal Theva perfectly.
Comment from 10 September 2026 — Experience from 28 August 2026
Krystian
The stands are sturdy, easy to assemble, and match the Theva N1 perfectly. Great value and highly recommended!
Comment from 28 July 2026 — Experience from 17 July 2026
Bernard
Perfect complement to the speakers and nice design.
Comment from 14 February 2025 — Experience from 25 November 2022
* Attention ! Un crédit coûte de l'argent et doit être remboursé
Pour un achat de 300 € en 4 fois : acompte de 75 €, puis 3 mensualités de 75 €. Crédit de 225 € au taux débiteur fixe de 0% sur 3 mois. Coût du crédit 0 €. Montant total dû 300 €. TAEG 0%. Le coût du crédit est pris en charge par l'enseigne.
Sous réserve d'acceptation par Alma SAS (almapay.com), société de financement agréée par l'ACPR (code CIB : 17408). RCS Nanterre 839100575. Contact : support@almapay.com