Laurent
Perfectly suited for my JVC 7900 projector.
Comment from 8 July 2020 — Experience from 17 June 2020
A projector mounted directly against a high ceiling often projects its image above the screen, and the digital keystone correction applied as a result comes at the expense of sharpness. The simplest solution is mechanical: this 22.9 cm black aluminium column screws between the ceiling plate and the projector mount, lowers the assembly by that amount and routes cables inside the tube.
The CMS009 belongs to the Speed-Connect system from Chief, which divides a ceiling installation into three elements screwed together: a plate secured to the structure, a column that sets the distance, then the mount that holds the projector. The column does just one thing, but it does it precisely: it lowers the lens by 22.9 cm, plus the thickness of the plate and mount. This height matters, because a properly positioned projector falls within its lens’s optical shift range (lens shift) and projects a rectangular image without digital processing. This is a fixed column, with no sliding or telescopic adjustment, so it requires measuring before ordering but provides a single-piece component with no play.
Each end of the column has a 1.5-inch NPT thread, an American pipe thread standard with a slightly tapered profile that ensures a firm connection. The 3.81 cm figure corresponds to this nominal designation (1.5 inches), not to the tube’s outside diameter, which is close to 48 mm. This thread is common to all Chief ceiling plates and accessories using the same standard: the CMS009 fits onto a flat plate, an offset plate or a suspended ceiling kit, and accepts the projector mount below. Several columns can be joined end to end using a threaded coupling to achieve a length not listed in the catalogue, hence the range’s modular or custom assembly approach.
The aluminium tube keeps the suspended assembly lighter while offering a load capacity of 226.8 kg, far beyond the weight of a home projector, which rarely exceeds a few dozen kilos. In practice, an installation’s limit is determined by the weakest link in the chain: the projector mount, the plate and, above all, the ceiling anchorage, which must transfer the load to a supporting structure. The tube is hollow and has a cable exit opening: the power cable and HDMI cable run down inside the column and emerge near the projector, with no visible conduit along the tube. It is best to pull them through before the assembly is finally screwed together. The black finish matches dark projectors and dedicated rooms with dark ceilings, where a light-coloured tube would catch the eye in stray light.
The CMS009 occupies an intermediate position among Chief’s fixed columns, available in 7.6 cm, 15.2 cm, 22.9 cm, 30.5 cm and 61 cm lengths, followed by much longer lengths for high ceilings. When the exact distance is not known before installation, the adjustable columns in the same range cover spans of 15 to 23 cm, 30 to 46 cm, 46 to 61 cm and up to 1.83 m, with on-site adjustment. The fixed column remains the neatest solution when the dimension has been measured: a single component, more discreet than a telescopic tube and with no locking collar to keep an eye on.
No. The CMS009 is sold separately. It must be paired with a ceiling plate with a 1.5-inch NPT thread and a compatible projector mount, selected according to the ceiling type and projector model.
Start with the height at which the lens needs to be positioned, as specified in the projector’s manual based on the screen size and lens shift range. The distance between the ceiling and this height, minus the thickness of the mounting plate and the bracket, gives the required column length. If the result falls between two fixed lengths, an adjustable column or two columns joined with a coupling sleeve solves the problem.
This is not a good idea: the threading is only at the two ends, and a column cut to length loses one of its connections. For an intermediate height, the adjustable range is the intended option.
Yes, provided you use a kit designed for suspended ceilings. The Speed-Connect range includes several that transfer the load to the structure above the ceiling tiles or replace a tile with a mounting panel. The column then screws into the underside of this kit, just as it would with a standard mounting plate.
Any accessory with a 1.5-inch NPT thread screws into it mechanically. However, this standard is not universal in Europe, where some mounts use other thread pitches or clamped tubes: the exact thread designation must be checked before combining parts from different sources.
Yes. With a ceiling mount for a flat-screen display featuring the same connector, the column lowers a television or monitor in the same way. The screen’s weight must remain within the limits of the mount and anchoring, which are almost always lower than the column’s limit.
Yes, a white version of the same length (CMS009W) is available for light-colored ceilings, where it blends in better than a black tube.
Laurent
Perfectly suited for my JVC 7900 projector.
Comment from 8 July 2020 — Experience from 17 June 2020