Furutech Lan-8 NCF Plus 2.5m
Furutech LAN-8 NCF Plus, Cat 8 audiophile network cable
Between the router, the switch and the network player, an Ethernet cable does not carry sound but data packets. Why, then, give it such a sophisticated construction? The answer lies not in speed, which is more than sufficient with any cable, but in the noise that travels along the connection and interferes with the sensitive stages of a DAC. The LAN-8 NCF Plus addresses this issue through materials and shielding rather than speed.
Speed is not the real issue
Category 8 supports 40 Gb/s and bandwidth up to 2,000 MHz. A high-resolution audio stream, even in multichannel or DSD, requires only a few megabits per second. The margin is therefore huge, and it is not what distinguishes this cable from an ordinary lead.
Ethernet works with packets, error detection and retransmission: data arrives intact, or is sent again, regardless of the cable. What a shielded, non-magnetic and damped connection aims to contain is the high-frequency noise circulating alongside the signal: RF noise, electromagnetic interference, and noise carried by the switching power supply of a switch or router. This noise can couple with the analogue circuits and clock of the network player, raise the noise floor and disrupt synchronisation during conversion. The extent of the audible improvement depends on the ability of the following component to reject this interference: a streamer that is already well isolated will show a subtler difference than more exposed electronics.
Solid silver-plated conductors
The fundamental change compared with the original LAN-8 NCF is the move from stranded conductors to solid-core conductors. A solid core maintains its geometry better over the entire length and keeps a more consistent characteristic impedance, which matters at the high frequencies used by Category 8. Each conductor is 24 AWG (1/0.525), made from silver-plated α (Alpha) OCC copper. OCC refers to a continuous casting process that limits grain boundaries in the copper.
Silver plating has a genuine benefit here: at Cat 8 bandwidth, close to 2 GHz, the skin effect concentrates current at the conductor surface, and this more conductive silver surface carries the fast components. This differs from analogue audio, where the skin effect remains marginal. The twisted pairs retain a calculated twist pitch to enhance RF rejection and limit crosstalk. The trade-off of a solid core is that the cable is stiffer than a stranded one, requiring care with its bend radius.
Three layers against interference
The construction is S/FTP: foil around each pair and a braided shield around the whole assembly. The triple shielding combines aluminium foil and a copper braid. The foil continuously covers high frequencies, while the braid handles lower electromagnetic interference, ensures mechanical continuity and serves as a ground path. This dual approach fulfils the two roles expected of a network cable in an audio context: preventing external interference from entering and stopping internal noise from radiating towards nearby equipment. Category 8 already requires complete shielding; here, it is reinforced, in keeping with the increased diameter.
Non-magnetic connectors and NCF shell
The plugs are RJ45 in 8P8C format. The contacts use a non-magnetic α conductor with thick 24-carat gold plating, while the body is made of 24-carat gold-plated copper alloy with low magnetic properties. The non-magnetic choice addresses a specific issue: the magnetic underlayers often found beneath gold plating can introduce contact distortion through eddy currents and hysteresis. Avoiding them keeps the connection cleaner.
The connector shell uses NCF (Nano Crystal² Formula) material from Furutech, a hybrid multi-material construction. This crystalline compound has two properties: it generates negative ions that dissipate static charges, and it converts thermal energy into far-infrared radiation. Furutech combines it with nanometric ceramic particles and carbon powder for a piezoelectric damping effect. The role of this shell is to damp micro-vibrations and dissipate static charges where the cable joins the socket.
Nylon sleeve, diameter and flexibility
The outer jacket is made of flexible black PVC, UL/CL3-rated for flammability (suitable for in-wall installation) and RoHS-compliant. Over it, a braided nylon sleeve protects the entire assembly and helps damp resonances. The outer diameter reaches approximately 8.0 ± 0.15 mm, compared with 7.0 mm on the previous LAN-8 NCF; this added cross-section accommodates the reinforced shielding. With solid cores and this diameter, the cable remains firm: it is best to allow some space behind the furniture and maintain a reasonable bend radius when connecting it.
Connection direction and lengths
The cable is directionally marked. An arrow indicates the input side, meaning the source: the arrow should therefore point towards the transmitting device, the router or switch supplying the player. Connecting the cable in reverse will not damage either the cable or the equipment, but the marked direction is the one selected for the best performance. Standard lengths range from 0.6 m to 5 m (0.6 / 1.2 / 1.8 / 2.5 / 3.6 / 5 m), with 7.5 m and 10 m available on request. As the RJ45 plug is universal and Category 8 is backward-compatible with Cat 7 and Cat 6, the cable can be installed at any point in the network and works with all Ethernet equipment.
Technical Specifications
Overview
- Type: high-performance Ethernet cable
- Category: Category 8 (Cat 8)
- Purpose: designed for high-speed Ethernet networks and high-resolution digital audio systems
- Intended use: high-end and audiophile Ethernet installations
- Compatibility: backward compatible with Cat 7 and Cat 6 categories
- Compliance: RoHS
Transmission Performance
- Maximum speed: up to 40 Gb/s
- Bandwidth: up to 2,000 MHz
- Solid-core construction for more stable transmission
- Reduced crosstalk and transmission noise
Architecture and Conductors
- Architecture: S / FTP twisted-pair cable
- Conductors: silver-plated α (Alpha) OCC copper
- Gauge: 24 AWG (1 / 0.525)
- Minimized transmission losses
- Furutech NCF (Nano Crystal² Formula) technology
- Mechanical damping
- Reduced static charges
Connectors
- Connectors: RJ45 / 8P8C
- Non-magnetic α conductors
- Contact finish: 24-karat gold plating
- Connector bodies: 24K gold-plated copper alloy, with low magnetic properties
Shielding and Protection
- Triple shielding with aluminum foil and copper braid
- Enhanced protection against electromagnetic interference
- Reduced noise and crosstalk
Mechanical Construction and Jacketing
- Outer diameter: approximately 8.0 ± 0.15 mm (increased compared with the previous LAN-8 NCF)
- Outer jacket: flexible black PVC, UL / CL3 flame-retardant rating
- Covering: nylon braided sleeve contributing to resonance damping
- Insulation and damping: materials selected to reduce internal vibrations and resonances
Available Lengths
- Standard: 0.6 m, 1.2 m, 1.8 m, 2.5 m, 3.6 m, 5 m
- On request: 7.5 m and 10 m
Key Features
- 40 Gb/s and 2,000 MHz for very high-speed transmission
- Triple shielding for better isolation against electromagnetic interference
- Silver-plated OCC conductors to minimize transmission losses
- 24K gold-plated RJ45 connectors
- NCF technology for mechanical damping and reduced static charges
- Solid-core construction improving transmission stability
- Increased diameter to 8 mm compared with the previous LAN-8 NCF
- Reduced crosstalk and transmission noise
- Braided nylon jacket contributing to resonance damping
- Intended for high-end and audiophile Ethernet installations
Frequently Asked Questions
Where should it be placed in the network chain to get the most out of it?
The final segment before the network player is where conducted noise matters most, since that is where it can reach sensitive circuits. In practice, the link between the switch and the streamer is often the priority. Adding a carefully designed link further upstream, between the router and the switch, extends this approach without being a prerequisite.
Is it compatible with a network that is not Cat 8?
Yes. An Ethernet link operates at the lowest category in the chain, so when connected to a Cat 5e or Cat 6 network, it does not unlock Cat 8’s 40 Gb/s. However, its audio benefit does not come from this speed: the shielding, conductors and connectors affect noise on the relevant segment, regardless of the negotiated speed. Backward compatibility with Cat 7 and Cat 6 is ensured.
Does solid-core cable interfere with repeated connections?
A solid-core conductor withstands repeated bending less well than a stranded cable. In a fixed installation, this is not a problem. It is best to avoid unplugging and reconnecting it often, and bending it tightly near the connectors.
Does it connect directly between a streamer and a DAC?
Only if the converter has an RJ45 network input, which remains rare. Most connections between a network player and a DAC use USB, coaxial or optical. The LAN-8 NCF Plus belongs on the network side, between Ethernet devices.
What does it offer over the original LAN-8 NCF?
Three developments: solid conductors instead of stranded conductors, a diameter increased to 8.0 mm from 7.0 mm, and reinforced shielding housed within this more generous cross-section. The rest of the formula—NCF material, silver-plated α OCC copper, non-magnetic 24-carat gold connectors—remains unchanged.
Can it be used with a TV, console or computer?
Yes. It is a standard Cat 8 cable with RJ45 plugs: it works with any Ethernet device. Its audio-oriented construction does not limit this general use; it simply adds shielding and material work that standard cables do not have.
Is silver plating beneficial for a digital connection?
At Cat 8 bandwidths, the skin effect becomes significant and drives the fast signal components toward the conductor’s surface. A silver surface, being a better conductor than copper, then carries these frequencies. This is what distinguishes the case of a high-frequency network cable from that of an analog audio cable, where the same argument would carry little weight.
- Eco-contribution included in the sale price.
